Site-wide links

Scholarly Works

Satish Kandlikar
Professor

2014 Submissions

Full Length Book

Kandlikar, S. G., et al. Heat Transfer and Fluid Flow in Minichannels and Microchannels. 2nd ed. Rochester, NY: Elsevier, 2014. Print.

Hayner, C.H., M. E. Steinke, and S.G. Kandlikar. Contemporary Perspectives on Liquid Cold Plate Design: Design and Manufacturing Liquid Cooled Heat Sinks for Electronics Cooling. Rochester, NY: Begell House, 2014. Print.

Journal Paper

Banerjee, R and S.G. Kandlikar. "Liquid Water Quantification in the Cathode Side Gas Channels of a Proton Exchange Membrane Fuel Cell Through Two-Phase Flow Visualization." Journal of Power Sources. 247 (2014): 9-19. Print. *

Banerjee, R and S.G. Kandlikar. "Experimental Investigation of Two-Phase Flow Pressure Drop Transients in Polymer Electrolyte Membrane Fuel Cell Reactant Channels and Their Impact on the Cell Performance." Journal of Power Sources. 268 (2014): 194-203. Print. *

Bhavnani, S, et al. "Boiling Augmentation with Micro/Nanostructured Surfaces: Current Status and Research Outlook." Nanoscale and Microscale Thermophysical Engineering. 18 (2014): 197-222. Print. *

Gopalan, P and S.G. Kandlikar. "Modeling Dynamic Interaction Between an Emerging Water Droplet and the Sidewall of a Trapezoidal Channel." Colloids and Surfaces A: Physicochemical and Engineering Aspects. 441 (2014): 262-275. Print. *

Gopalan, P and S.G. Kandlikar. "Effect of Channel Materials and Trapezoidal Corner Angles on Emerging Droplet Behavior in Proton Exchange Membrane Fuel Cell Gas Channels." Journal of Power Sources. 248 (2014): 230-238. Print. *

Gopalan, P and S.G. Kandlikar. "Contact Line Characteristics of Liquid-Gas Interfaces Over Grooved Surfaces." Microfluidics and Nanofluidics 16. 6 (2014): 999-1008. Print. *

A, Kalani, and Kandlikar, S. G. "Evaluation of Pressure Drop Performance During Enhanced Flow Boiling in Open Microchannels With Tapered Manifolds." Journal of Heat Transfer 136. 5 (2014): 1-7. Print. *

Kandlikar, S. G. "Review and Projections of Integrated Cooling Systems for Three-Dimensional Integrated Circuits." Journal of Electronic Packaging 136. 2 (2014): 1-11. Print. *

Kandlikar, S. G., et al. "Two-Phase Flow in GDL and Reactant Channels of a Proton Exchange Membrane Fuel Cell." International Journal of Hydrogen Energy 39. 12 (2014): 6620-6636. Print. *

Li, Z, and S.G. Kandlikar. "Current Status and Future Trends in Data Center Cooling Technologies." Heat Transfer Engineering. (2014) Print. *

T.Y., Lin,, et al. "An Experimental Investigation on Friction Characteristics and Heat Transfer of Air and CO2 Flow in Microtubes With Structured Surface Roughness,." Heat Transfer Engineering 35. 2 (2014): 021007-1 - 021007-11. Print. *

Patil, C. M. and S.G. Kandlikar. "Review of the Manufacturing Techniques for Porous Surfaces Used in Enhanced Pool Boiling." Heat Transfer Engineering 35. 10 (2014): 887-902. Print. *

Patil, C. M., K. S. V. Santhanam, and S.G. Kandlikar. "Development of a Two-step Electrodeposition Process for Enhancing Pool Boiling." International Journal of Heat Mass Transfer. 79 (2014): 989-1001. Print. *

Patil, C. M. and S.G. Kandlikar. "Pool Boiling Enhancement through Microporous Coatings Selectively Electrodeposited on Fin Tops of Open Microchannels." International Journal of Heat Mass Transfer. 79 (2014): 816-828. Print. *

Kandlikar, S. G. "Design Considerations for Cooling High Heat Flux IC Chips with Microchannels." IEEE DESIGN & TEST 31. 4 (2014): 43-50. Print. *

R, Banerjee, and Kandlikar, S. G. "Two-phase pressure drop response during load transients in a PEMFC,." Int. J. Hydrog. Energy. 39(33) (2014): 19079–19086. Print. *

Banerjee, R, et al. "Experimental Validation of Two-phase Pressure Drop Multiplier as a Diagnostic Tool for Characterizing PEM Fuel Cell Performance." International Journal of Hydrogen Energy 39. 31 (2014): 17791–17801. Print. *

Banerjee, R and S.G. Kandlikar. "Two-phase Pressure Drop Response During Load Transients in a PEMFC." International Journal of Hydrogen Energy 39. 33 (2014): 19079–19086. Print. *

Banerjee, R, et al. "Experimental Validation of Two-phase Pressure Drop Multiplier as a Diagnostic Tool for Characterizing PEM Fuel Cell Performance." International Journal of Hydrogen Energy 39. 31 (2014): 17791–17801. Print. *

Banerjee, R and S.G. Kandlikar. "Experimental Investigation of Two-Phase Pressure Drop Transients in Polymer Electrolyte Membrane Fuel Cell Reactant Channels and Their Impact on the Cell Performance." Journal of Power Sources 268. (2014): 194-203. Print. *

Book Chapter

Kandlikar, S. G. "Preface." Heat Transfer and Fluid Flow in Minichannels and Microchannels. Rochester, NY: Elsevier, 2014. prefact. Print. *

Published Conference Proceedings

Kalani, A and S.G. Kandlikar. "Pressure Drop Analysis Using the Homogeneous Model for Open Microchannel with Manifold (OMM)." Proceedings of the ASME 2014 12th International Conference on Nanochannels, Microchannels and Minichannels. Ed. Unknown. Chicago, IL: n.p., 2014. Print. *

Banerjee, R and S.G. Kandlikar. "Two Phase Pressure Drop Characteristics During Low Temperature Transients in PEMFCS." Proceedings of the ASME 2014 12th International Conference on Nanochannels, Microchannels and Minichannels. Ed. Unknown. Chicago, IL: n.p., 2014. Print. *

Invited Presentations/Keynotes

Kandlikar, S.G. "Microscale Transport – From Electronics Cooling to Fuel Cells." Invited Talk, Graduate Seminar Speaker. Ohio State University. Columbus, OH. 21 Mar. 2014. Keynote Speech. *

Kandlikar, S.G. "Transport Phenomenon at Microscale – From Electronics Cooling to Fuel Cells." Mechanical and Aerospace Graduate Seminar Speaker. University of Texas. Arlington, TX. 10 Apr. 2014. Keynote Speech.

Kandlikar, S.G. "Advances and Opportunities in Microscale Transport Research." Tsinghua University. Department of Mechanical Engineering. Beijing, China. 6 May 2014. Guest Lecture.

Kandlikar, S.G. "Pool Boiling on Multiscale Surface Features." International Heat Transfer Symposium. International Heat Transfer Symposium. Bejing, China. 6 May 2014. Guest Lecture.

Kandlikar, S.G. "Revival of Pool Boiling for High Heat Flux Dissipation." IEEE ITHERM 2014 Conference. IEEE ITHERM 2014 Conference. Orlando, Florida. 27 May 2014. Conference Presentation.

Kandlikar, S.G. "Recent Advances in Pool Boiling Heat transfer with Micro- and Nanostructures." INTEL Corp. INTEL Corp. Phoeniz, AZ. 4 Sep. 2014. Keynote Speech.

Kandlikar, S.G. "Recent Advances in Pool Boiling Heat transfer with Micro- and Nanostructures." Graduate Seminar Presentation. Arizona State University. Tempe, Arizona. 5 Sep. 2014. Keynote Speech.

Kandlikar,, . "Cooling Options for 3D-IC Cooling." IEEE Electronics Packaging Symposium. Binghamton Unviersity. Binghamton, New York. 8 Oct. 2014. Keynote Speech.

Kandlikar, S.G. "Hydrogen Economy and Recent Developments in Automotive Fuel Cells." Hydrogen Properties Research Center. Kyushu University. Fukuoka, Japan. 23 Oct. 2014. Keynote Speech.

Kandlikar, S.G. "Professor Shoji's Outstanding Contributions and Our Current Understanding of Boiling Phenomena." Invited Seminar at Boiling Workshop. Phase Change Research Committee of Thermal Engineering Division of JSME. Tokyo, Japan. 25 Oct. 2014. Keynote Speech.

Kandlikar, S.G. "Microscale Transport – From Fuel Cells to Electronics Cooling." MEM Seminar. Drexel University. Philadelphia, PA. 10 Apr. 2014. Keynote Speech.

Invited Article/Publication

Koz, M and S.G. Kandlikar. "The Effect of Injection and Suction on the Interfacial Mass Transport Resistance in a Proton Exchange Membrane Fuel Cell Air Channel." Proceedings of the 12th International Conference on Nanochannels, Microchannels, and Minichannels. (2014). Print. *

Raghupathi, P. and S. Kandlikar. "Evaporation Momentum Force on a Bubble Under Asymmetric Temperature Condition." International Mechanical Engineering Conference and Exposition. (2014). Print. *

2013 Submissions

Journal Paper

Dharaiya, V. V. and S. G. Kandlikar. "A Numerical Study on the Effects of 2D Structured Sinusoidal Elements on Fluid Flow and Heat Transfer at Microscale." International Journal of Heat and Mass Transfer 57. (2013): 190-201. Print. *

Gopalan, P. and S. G. Kandlikar. "Effect of Channel Material on Water Droplet Dynamics in a PEMFC Gas Channel." Journal of Electrochemical Society 160. 6 (2013): F487-F495. Print. *

Kalani, A. and S. G. Kandlikar. "Enhanced Pool Boiling with Ethanol at Subatmospheric Pressures for Electronics Cooling." Journal of Heat Transfer 135. (2013): 111002-1 - 111002-7. Print. *

Kandlikar, S. G. "Selected Papers from the Ninth International Conference on Nanochannels, Microchannels, and Minichannels." Heat Transfer Engineering 34. 2-3 (2013): 99-100. Print. *

Kandlikar, S. G. "Controlling Bubble Motion Over Heated Surface Though Evaporation Momentum Force to Enhance Pool Boiling Heat Transfer." Applied Physics Letters 102. (2013): 051611-1 - 051611-5. Print. *

Kandlikar, S. G., et al. "Enhanced Flow Boiling Over Open Microchannels with Uniform and Tapered Gap Manifolds." Journal of Heat Transfer 135. (2013): 061401-1 061401-9. Print. *

Kandlikar, S. G., et al. "Heat Transfer in Microchannels - 2012 Status and Research Needs." Journal of Heat Transfer 135. 9 (2013): 091001-1 - 091001-18. Print. *

Koz, M. and S. G. Kandlikar. "Numerical Investigation of Interfacial Transport Resistance Due to Water Droplets in Proton Exchange Membrane Fuel Cell Air Channels." Journal of Power Sources 243. (2013): 946-957. Print. *

Lin, T-Y. and S. G. Kandlikar. "Heat Transfer Investigation of Air Flow in Microtubes - Part I: Effects of Heat Loss, Viscous Heating, and Axial Conduction." Journal of Heat Transfer 135. 3 (2013): 031703-1 - 031703-9. Print. *

Lin, T-Y. and S. G. Kandlikar. "Heat Transfer Investigation of Air Flow in Microtubes - Part II: Scale and Axial Conduction Effects." Journal of Heat Transfer 135. 3 (2013): 031704-1 - 031703-6. Print. *

Mehta, J. S. and S. G. Kandlikar. "Pool Boiling Heat Transfer Enhancement over Cylindrical Tubes with Water at Atmospheric Pressure, Part I: Experimental Results for Circumferential Rectangular Open Microchannels." International Journal of Heat and Mass Transfer 64. (2013): 1205-1215. Print. *

Mehta, J. S. and S. G. Kandlikar. "Pool Boiling Heat Transfer Enhancement over Cylindrical Tubes with Water at Atmospheric Pressure, Part II: Experimental Results and Bubble Dynamics for Circumferential V-Groove and Axial Rectangular Open Microchannels." International Journal of Heat and Mass Transfer 64. (2013): 1216-1225. Print. *

Rubio-Jimenez, C. A., S. G. Kandlikar, and A. Hernandez-Guerrero. "Performance of Online and Offset Micro Pin-Fin Heat Sinks with Variable Fin Density." IEEE Transactions on Components, Packaging, and Manufacturing Technology 3. 1 (2013): 86-93. Print. *

Published Conference Proceedings

Banerjee, R., E. J. See, and S. G. Kandlikar. "Pressure Drop and Voltage Response of PEMFC Operation under Transient Temperature and Loading Conditions." Proceedings of the 224th ECS Meeting. Ed. H. Gasteiger, et al. San Francisco, CA: Electrochemical Society, 2013. Print. *

Kalani, A. and S. G. Kandlikar. "Preliminary Results of Pressure Drop Modeling During Flow Boiling in Open Microchannels with Uniform and Tapered Manifolds (OMM)." Proceedings of the ASME 2013 International Mechanical Engineering Congress & Exposition. San Diego, CA: American Society of Mechanical Engineers, 2013. Web. *

Kalani, A. and S. G. Kandlikar. "Experimental Investigation of Flow Boiling Performance of Open Microchannels with Uniform and Tapered Manifolds (OMM)." Proceedings of the ASME 2013 Summer Heat Transfer Conference. Minneapolis, MN: American Society of Mechanical Engineers, 2013. Web. *

Kalani, A. and S. G. Kandlikar. "Pool Boiling Heat Transfer with Binary Mixture on Open Microchannel Surface." Proceedings of the ASME 2013 11th International Conference on Nanochannels, Microchannels, and Minichannels. Sapporo, Japan: American Society of Mechanical Engineers, 2013. Web. *

See, E. J. and S. G. Kandlikar. "Effect of GDL Material on Thermal Gradients along the Reactant Flow Channels in PEMFCs." Proceedings of the 224th ECS Meeting. Ed. H. Gasteiger, et al. San Francisco, CA: Electrochemical Society, 2013. Print. *

Invited Presentations/Keynotes

Kandlikar, S. G. "Plenary Speaker: Two-Phase Flow in GDL and Reactant Channels of a Proton Exchange Membrane Fuel Cell." 8th International Conference on Multiphase Flow. Pohang University of Science and Technology. Jeju, Korea. 26 May 2013. Keynote Speech. *

Kandlikar, S. G. "Plenary Speaker: Flow Boiling in Microchannels - A New Pathway to Unprecedented Heat Transfer Performance Through OMM Design." 9th UK - Japan Seminar on Multi-Phase Flows 2013. Brunel University. London, United Kingdom. 16 Sep. 2013. Keynote Speech. *

2012 Submissions

Journal Paper

Kandlikar, S.G. and D. Cooke. "Effect of Open Microchannel Geometry on Pool Boiling Enhancement." International Journal of Heat and Mass Transfer 55. 4 (2012): 1004-1013. Print. *

Kandlikar, S.G. and Michael Daino. "3D Phase-Differentiated GDL Microstructure Generation with Binder and PTFE Distributions." International Journal of Hydrogen Energy 37. 6 (2012): 5180-5189. Print. *

Kandlikar, S.G. and V.V. Dharaiya. "Numerical Investigation of Heat Transfer in Rectangular Microchannels Under H2 Boundary Condition During Developing and Fully Developed Laminar Flow." Journal of Heat Transfer 134. 2 (2012): 1-10. Print. *

Kandlikar, S.G. and Preethi Gopalan. "Droplet-Sidewall Dynamic Interactions in PEMFC Gas Channels." Journal of Electrochemical Society. (2012): 468-475. Print. *

Kandlikar, S.G., Evan See, and M Grimm. "Modeling Gas Flow in PEMFC Channels: Part I Flow Pattern Transitions and Pressure Drop in a Simulated Ex Situ Channel with Uniform Water Injection Through the GDL." International Journal of Hydrogen Energy. (2012): 12489-12503. Print. *

Kandlikar, S.G. "Closure to Discussion of Heat Transfer Mechanisms During Flow Boiling in Microchannels." Journal of Heat Transfer. (2012): 015502-1. Print. *

Kandlikar, S.G., M. H. Kim, and S. Peter. "Guest Editorial." Journal of Heat Transfer. (2012): 20301. Print. *

Kandlikar, S.G. "History, Advances, and Challenges in Liquid Flow and Flow Boiling Heat Transfer in Microchannels: A Critical Review." Journal of Heat Transfer. (2012): 034001-1-10. Print. *

Kandlikar, S.G. "A Theoretical Model for Axial Heat Conduction Effects During Single-Phase Flow in Microchannels." Journal of Heat Transfer. (2012): 020902-020908. Print. *

Kandlikar, S.G., C. A. Rubio-Jimenez, and A. Hernandez-Guerrero. "Numerical Analysis of Novel Micro Pin Fin Heat Sink with Variable Fin Density." IEEE Transactions on Components, Packaging and Manufacturing Technology. (2012): 825-833. Print. *

Yang, C. Y., et al. "Heat Transfer and Friction Characteristics of Air Flow in Microtubes." Experimental Thermal and Fluid Science. (2012): 12-18. Print. *

Yao, Z., Y. W. Lu, and S. G. Kandlikar. "Fabrication of Nanowires on Orthogonal Surfaces of Microchannels and Their Effect on Pool Pooling." Journal of Micromechanics and Microengineering. (2012): 115005-115014. Print. *

Wagner, R.N. and S. G. Kandlikar. "Effects of Structured Roughness on Fluid Flow at the Microscale Level." Heat Transfer Engineering. (2012): 483-493. Print. *

Zhang, G. and S. G. Kandlikar. "A Critical Review of Cooling Techniques in Proton Exchange Membrane Fuel Cell Stacks." International Journal of Hydrogen Energy. (2012): 2412-2429. Print. *

Kandlikar, S.G. and T.Y. Lin. "An Experimental Investigation of Structured Roughness Effect on Heat Transfer During Single-Phase Liquid Flow at Microscale." Journal of Heat Transfer. (2012): 101701-1 - 101701-9. Print. *

Kandlikar, S.G., Z. Yao, and Y-w Lu. "Pool Boiling Heat Transfer Enhancement through Nanostructures on Silicon Microchannels." Journal of Nanotechnology and Medicine. (2012): 031002-1 - 031002-8. Print. *

Kandlikar, S.G., et al. "Professor Warren M. Rohsenow (1921-2011)." International Journal of Heat and Mass Transfer. (2012): 4938-4940. Print. *

Published Conference Proceedings

Gopalan, P. and S. G. Kandlikar. "Effect of Channel Material on the Behavior of Water Droplet Emerging from the GDL into the PEMFC Gas Channels." Proceedings of the ECS 222nd Meeting. Ed. Hubert Gasteiger. Honolulu, HI: n.p., 2012. Web. *

Gopalan, P. and S. G. Kandlikar. "Contact Line Characteristics of Liquid-Gas Interfaces Over Confined/Structured Surfaces." Proceedings of the 3rd European Conference on Microfluidics. Ed. Hubert Gasteiger. Heidelberg, Germany: n.p., 2012. Web. ∆

Kalani, A. and S. G. Kandlikar. "Pool Boiling Heat Transfer over Microchannel Surfaces With Ethanol at Atmospheric Pressure." Proceedings of the ASME 2012 10th International Conference on Nanochannels, Microchannels, and Minichannels. Ed. Hubert Gasteiger. Rio Grande, Puerto Rico: n.p., Web.

Gopalan, P. and S. G. Kandlikar. "Effect of Channel Material on the Behavior of Water Droplet Emerging from the GDL into the PEMFC Gas Channels." Proceedings of the ECS 222nd Meeting. Ed. 222. Honolulu, HI: n.p., 2012. Web.

Koz, M. and S. G. Kandlikar. "Numerical Simulation of the Interfacial Oxygen Transport Resistance for a PEMFC Cathode Incorporating Water Droplet Coverage." Proceedings of the ECS 222nd Meeting. Ed. Hubert Gasteiger. Honolulu, HI: n.p., 2012. Web.

Koz, M. and S. G. Kandlikar. "A Preliminary Study for 3D Numerical Simulation of a Through-Plane Temperature Profile in a PEMFC Incorporating Coolant Channels." Proceedings of the ASME 2012 10th International Conference on Nanochannels, Microchannels, and Minichannels. Ed. Hubert Gasteiger. Rio Grande, Puerto Rico: n.p., 2012. Web.

Mehta, J. and S. G. Kandlikar. "Heat Transfer Enhancement During Pool Boiling Of Water Over Horizontal And Vertical Tubes With Micro Structured Surfaces." Proceedings of the Proceedings of the ASME 2012 10th International Conference on Nanochannels, Microchannels, and Minichannels. Ed. Hubert Gasteiger. Rio Grande, Puerto Rico: n.p., 2012. Web.

Rubio-Jimenez, C.A. "Thermal Management in 3D IC Stacks formed by Multicore Processors." Proceedings of the Design Automation Conference 12. Ed. Hubert Gasteiger. San Francisco, CA: n.p., 2012. Web.

See, E.J. and S. G. Kandlikar. "A Two-Phase Pressure Drop Model Incorporating Local Water Balance in PEM Fuel Cell Gas Channels." Proceedings of the ECS 222nd Meeting. Ed. Hubert Gasteiger. Honolulu, HI: n.p., 2012. Web. *

Yao, Z., Lu, Y. W, and S. G. Kandlikar. "Micro/Nano Hierarchical Structure in Microchannel Heat Sink for Boiling Enhancement." Proceedings of the 25th International Conference on Micro Electro Mechanical Systems. Ed. Hubert Gasteiger. Paris, France: n.p., 2012. Web. *

2011 Submissions

Journal Paper

Cooke, D. and S. G. Kandlikar. "Pool Boiling Heat Transfer and Bubble Dynamics Over Plain and Enhanced Microchannels." Journal of Heat Transfer 133. 5 (2011): 052902-1-9. Print. £

Daino, M. M., et al. "Through-Plane Water Transport Visualization in a PEMFC by Visible and Infrared Imaging." Electrochemical and Solid-State Letters 14. 6 (2011): B51-B54. Print. £

Kandlikar, S. G., M.L. Garoalo, and Z. Lu. "Water Management in a PEMFC: Water Transport Mechanism and Material Degradation in Gas Diffusion Layers." Fuel Cells 11. 6 (2011): 814-823. Print. £

Kandlikar, S. G. "Selected Papers from the Seventh International Conference on Nanochannels, Microchannels, and Minichannels." Heat Transfer Engineering 32. 7-8 (2011): 525-526. Print. £

LaManna, J. M. and S. G. Kandlikar. "Determination of Effective Water Vapor Diffusion Coefficient in Pemfc Gas Diffusion Layers." International Journal of Hydrogen Energy 36. 8 (2011): 5021-5029. Print. £

Lu, Z., et al. "Water Management Studies in PEM Fuel Cells, Part IV: Effects of Channel Surface Wettability, Geometry and Orientation on The Two-phase Flow in Parallel Gas Channels." International Journal of Hydrogen Energy 36. 16 (2011): 9864-9875. Print. £

Lu, Y. W. and S. G. Kandlikar. "Nanoscale Surface Modification Techniques for Pool Boiling Enhancementa A Critical Review and Future Directions." Heat Transfer Engineering 32. 10 (2011): 827-842. Print. £

Mukherjee, A., S. G. Kandlikar, and Z. J. Edel. "Numerical Study of Bubble Growth and Wall Heat Transfer During Flow Boiling in a Microchannel." International Journal of Heat and Mass Transfer 54. (2011): 3702-3718. Print. £

Rath, C. D. and S. G. Kandlikar. "Liquid Filling in a Corner with A Fibrous wall An Application To Two-phase Flow in PEM Fuel Cell Gas Channels." Colloids and Surfaces A: Physicochemical and Engineering Aspects 384. 1-3 (2011): 653-660. Print. £

Sergi, K. M. and S. G Kandlikar. "Quantification and Characterization of Water Coverage in PEMFC Gas Channels Using Simultaneous Anode and Cathode Visualization and Image Processing." International Journal of Hydrogen Energy 36. 19 (2011): 12381-12392. Print. £

Yao, Z., Y.-W Lu, and S. G. Kandlikar. "Effects of Nanowire Height on Pool Boiling Performance of Water on Silicon Chips." International Journal of Thermal Sciences 50. 11 (2011): 2084-2090. Print. £

Lao, Z., Y. W. Lu, and S. G. Kandlikar. "Direct Growth of Copper Nanowires on a Substrate for Boiling Applications." Micro & Nano Letters 6. 7 (2011): 563-566. Print. £

Published Conference Proceedings

Banerjee, R. and S. G. Kandlikar. "Effect of Temperature on In-Plane Permeability of Water Vapor in the Gas Diffusion Layer of PEM Fuel Cells." Proceedings of the Electrochemical Society Transactions. Ed. H. Gasteiger. unknown: n.p., 2011. Print.

Daino, M. M. and S. G. Kandlikar. "Advances in Digital Microstructure Generation of a PEMFC GDL with Localized Binder and PTFE Distributions." Proceedings of the 4th European Fuel Cell Piero Lunghi Conference & Exhibition. Ed. EFC11275. Rome, Italy: n.p., 2011. Print.

Dharaiya, V. V. and S. G. Kandlikar. "A Numerical Study to Predict the Effects of Structured Roughness Elements on Pressure Drop and Heat Transfer Enhancement in Minichannels and Microchannels." Proceedings of the ASME 2011 International Mechanical Engineering Congress and Exposition: Energy and Water Scarcity. Ed. IMECE2011-65262. Denver, CO: n.p., 2011. Print.

Garfolo, M. L. and S. G. Kandlikar. "Gas Diffusion Layer Material Degradation Mechanisms and Their Effect on Water Breakthrough Dynamics in Proton Exchange Membrane Fuel Cells." Proceedings of the 4th European Fuel Cell Piero Lunghi Conference & Exhibition. Ed. EFC11239. Rome, Italy: n.p., 2011. Print.

Gopalan, P. and S. G. Kandlikar. "Investigation of Water Droplet Interaction with the Side Wall of the Gas Channel in the PEM Fuel Cell in the Presence of Gas Flow." Proceedings of the Electrochemical Society Transactions. Ed. H. Gasteiger et al. Boston, MA: n.p., 2011. Print.

Kandlikar, S. G., D. Kudithipudi, and C. A. Rubio-Jimenez. "Cooling Mechanisms in 3D ICs: Thermo-Mechanical Perspective." Proceedings of the 2011 International Green Computing Conference and Workshops. Ed. IEEE. Orlando, Fl: n.p., Print.

Rath, C. D. and S. G. Kandlikar. "Effect of Channel Geometry on Two-Phase Flow Structure in Fuel Cell Gas Channels." Proceedings of the ASME 2011 9th International Conference on Nanochannels, Microchannels, and Minichannels. Ed. ICNMM2011-58252. Edmonton, AB, Canada: n.p., 2011. Print.

See, E. J., et al. "Thermal Management Considerations in the Design of an Experimental Fuel Cell with Material Evaluation." Proceedings of the 4th European Fuel Cell - Piero Lunghi Conference & Exhibition. Ed. EFC11237. Rome, Italy: n.p., 2011. Print.

Yang, C. Y., et al. "An Experimental Investigation on Heat Transfer Characteristics of Air and CO2 in Microtubes." Proceedings of the ASME 2011 9th International Conference on Nanochannels, Microchannels, and Minichannels. Ed. ICNMM2011-58102. n.p., 2011. Print.

Invited Presentations/Keynotes

Kandlikar, S. G. "Challenges of High Heat Flux Removal with Single-Phase and Flow Boiling Heat Transfer." International Forum on Frontier Theories of Thermal Science. International Forum on Frontier Theories of Thermal Science. Tsinghua University, Beijing, China. 18-20 Dec. 2011. Keynote Speech.

Kandlikar, S. G. "An Experimental Investigation of Structured Roughness on Heat Transfer During Single Phase Liquid flow at Microscale." Proceedings of the 3rd Micro and Nano Flows Conference. Micro and Nano Flows Conference. Makedonia Palace Hotel, Thessaloniki, Greece. 22-24 Aug. 2011. Address.

2010 Submissions

Formal Presentation

Dharaiya, V.V., R.R. Srivastava, and S.G. Kandlikar. “Numerical Investigation of Heat Transfer Effects in Microchannels under H2 Boundary Condition.” 2010 ITC 14th International Heat Transfer Conference. Washington, DC. 8-13 August 2010. Presentation. †

Lu, Yen-Wen, and S.G. Kandlikar. “Review of Nanoscale Surface Modification Techniques for Pool Boiling Enhancement.” ASME International Conference on Nanochannels, Microchannels, and Minichannels (ICNMM). Montreal, Canada. 30 Aug. - 1 Sept. 2010. Presentation.

Kandlikar, S.G., Z. Lu, and M. L. Garofalo. “Water Management in a PEMFC: Water Transport Mechanism and Material Degradation in Gas Diffusion Layers.” 2nd CARISMA International Conference on Progress in MEA Materials for Medium and High Temperature Polymer Electrolyte Fuel Kate Gleason College of Engineering Cells. La Grande Motte, France. 19-22 Sept. 2010. Presentation. †

Editor (book or journal)

Kandlikar, S.G., ed. Heat Exchanger Design Handbook. Redding, CT: Begell House, 2010. Print.

Published Article

Kandlikar, S. G. “1. Scale effects on flow boiling heat transfer in microchannels: A fundamental perspective.” International Journal of Thermal Sciences, 132.7 (2010): 1073-1085. Print.

Kandlikar, S. G. “A Scale Analysis Based Theoretical Force Balance Model for Critical Heat Flux (CHF) During Saturated Flow Boiling in Microchannels and Minichannels.” Journal of Heat Transfer, 132.8 (2010): 081501-1-13. Print.

Brackbill, T.P., and S.G. Kandlikar. “Application of Lubrication Theory and Study of Roughness Pitch During Laminar, Transition, and Low Reynolds Number Turbulent Flow at Microscale.” Heat Transfer Engineering, 31.8 (2010): 634-645. Print. †≠

Lu, Z., M.M. Daino, C. Rath, and S.G. Kandlikar. “Water Management Studies in PEM Fuel Cells, Part III: Dynamic Breakthrough and Intermittent Drainage Characteristics from GDLS with and without MPLS.” International Journal of Hydrogen Energy, 35.9 (2010): 4222-4233. Print. †≠

Kandlikar, S. G. “Similarities and Differences Between Flow Boiling in Microchannels and Pool Boiling.” Heat Transfer Engineering, 31.3 (2010): 159-167. Print. *